A5 Calibration Block (Metric Version) Special Alloy Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: Special Alloy

A5 Calibration Block (Metric Version) 1018 Steel Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: 1018 Steel

A5 Calibration Block (Metric Version) STAINLESS STEEL 304 Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: STAINLESS STEEL 304.

A5 Calibration Block (Metric Version) STAINLESS STEEL 316 Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: STAINLESS STEEL 316.

A5 Calibration Block (Metric Version) TITANIUM Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: TITANIUM.

A5 Calibration Block (Metric Version) ALUMINUM 7075-T6 Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: ALUMINUM 7075-T6

A5 Calibration Block (Metric Version) INCONEL 625 Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: INCONEL 625.

A5 Calibration Block (Metric Version) MONAL 800 Used for beam profile measurement of angle beam transducers and measurement of transducer angles. Block A5 used for calibrates resolution check for angle beam transducer, also used for angle beam plotting, to plot beam divergence for shear wave transducer. Analysis of amplitude with respect to exit point is carried out for each angle using data points from depths corresponding to side drilled holes in an IOW block (British Standards A5). Graphed and tabulated results are analyzed for trends. This modeling analysis is then compared to actual lab results for refracted angle determination. Geometry: Contains nine 1.5mm diameter x 22mm deep side drilled holes. Dimensions: 305mm (L) x 75mm(H) x 50mm (W). Material: MONAL 800.