K2 Calibration Test Block (0.5" Inch Version) Special Alloy The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: Special Alloy

K2 Calibration Test Block (0.5" Inch Version) 1018 Steel The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: 1018 Steel

K2 Calibration Test Block (0.5" Inch Version) STAINLESS STEEL 304 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: STAINLESS STEEL 304.

K2 Calibration Test Block (0.5" Inch Version) STAINLESS STEEL 316 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: STAINLESS STEEL 316.

K2 Calibration Test Block (0.5" Inch Version) TITANIUM The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: TITANIUM.

K2 Calibration Test Block (0.5" Inch Version) ALUMINUM 7075-T6 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: ALUMINUM 7075-T6

K2 Calibration Test Block (0.5" Inch Version) INCONEL 625 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: INCONEL 625.

K2 Calibration Test Block (0.5" Inch Version) MONAL 800 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.5" thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1" and 2" radius, 0.05"mm hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3" (L) x 1.7" (W) x 0.5" (T) Material: MONAL 800.

K2 Calibration Test Block (0.8” INCH VERSION) Special Alloy The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: Special Alloy

K2 Calibration Test Block (0.8” INCH VERSION) 1018 Steel The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: 1018 Steel

K2 Calibration Test Block (0.8” INCH VERSION) STAINLESS STEEL 304 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: STAINLESS STEEL 304.

K2 Calibration Test Block (0.8” INCH VERSION) STAINLESS STEEL 316 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: STAINLESS STEEL 316.

K2 Calibration Test Block (0.8” INCH VERSION) TITANIUM The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: TITANIUM.

K2 Calibration Test Block (0.8” INCH VERSION) ALUMINUM 7075-T6 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: ALUMINUM 7075-T6

K2 Calibration Test Block (0.8” INCH VERSION) INCONEL 625 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: INCONEL 625.

K2 Calibration Test Block (0.8” INCH VERSION) MONAL 800 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 0.8” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 0.8” (T) Material: MONAL 800.

K2 Calibration Test Block (1” INCH VERSION) Special Alloy The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: Special Alloy

K2 Calibration Test Block (1” INCH VERSION) 1018 Steel The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: 1018 Steel

K2 Calibration Test Block (1” INCH VERSION) STAINLESS STEEL 304 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: STAINLESS STEEL 304.

K2 Calibration Test Block (1” INCH VERSION) STAINLESS STEEL 316 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: STAINLESS STEEL 316.

K2 Calibration Test Block (1” INCH VERSION) TITANIUM The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: TITANIUM.

K2 Calibration Test Block (1” INCH VERSION) ALUMINUM 7075-T6 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: ALUMINUM 7075-T6

K2 Calibration Test Block (1” INCH VERSION) INCONEL 625 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: INCONEL 625.

K2 Calibration Test Block (1” INCH VERSION) MONAL 800 The miniature angle-beam is a calibration block that was designed for the US Air Force for use in the field for instrument calibration. The block is much smaller and lighter than the IIW block but performs many of the same functions. The miniature angle-beam block can be used to check the beam angle and exit point of the transducer. The block can also be used to make metal-distance and sensitivity calibrations for both angle and normal-beam inspection setups. 1” thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 1” and 2” radius, 0.2” hole, engraved reference mark scales from 35° to 75° degrees. Dimensions: 3” (L) x 1.7” (W) x 1” (T) Material: MONAL 800.